ALL STATES & TERRITORIES
Single outlet seed cup for Agrowdrill seed boxes to suit the single-gate system on older machines. Suits seed hoses with 31mm (1¼") diameter. Also ...
View full detailsSingle outlet seed cup for Agrowdrill seed boxes to suit the double-gate system. Double gate housings suit seed hoses with 38mm (1½") diameter. Th...
View full detailsBearing housing to suit bearings with outer diameter of 52mm, as found on the 15 notch disc assembly. Fits 138-3025
Double outlet seed cup for Agrowdrill seed boxes to suit the double-gate system. Double gate housings suit seed hoses with 38mm (1½") diameter. Th...
View full detailsSKF Carbon steel drive chain. Comes in a 3m length. Joiner links may be required. ANSI Chain Size: 10B-1 Strands: Single Pitch (mm): 15.875 or 5/8"...
View full detailsSpecial washers made for the seed box on Agrowdrills. Used on the gate arms and varibox adjustment arms.
This 20mm Hex Shaft is made out of 304 Stainless and is 3.6M long. A longer 4.8M stainless steel hex shaft is available here.The gate hex shaft is ...
View full detailsDouble outlet seed cup for Agrowdrill seed boxes to suit the single-gate system on older machines. Suits seed hoses with 31mm (1¼") diameter. Also ...
View full detailsThis flanged bearing housing is used to secure the 20mm spherical bearing to the Agrowdrill. Two are used per bearing assembly and are commonly fou...
View full detailsM18 threaded wheel nut, 1.5 pitch (fine thread). Total length is 65mm, useable thread is 40mm. Knurl is 19.5mm OD and 15mm Long
Suits Agr-Hub 1
This spacer ring has an ID of 60mm and is primarily used on Drive & Wheel arm assemblies.
This stainless steel screw tek is used to fasten the single gate and double gate housings to the hopper. Great care must be taken in ensuring that ...
View full details(x2) offsets are required to update an AD230. This is intended to shift the front tynes forward by 150mm in the case that the tyne is fitted with d...
View full detailsThis sprocket clutch assembly comes with 2 bearings installed to suit a 1" shaft (25.4mm). The overall length of the assembly is 110mm. The length ...
View full detailsSealed bearing, fits onto a 60mm shaft and is pressed into a machined sprocket or housing of 78mm in diameter. Commonly utilised in JPC2000 Wheel ...
View full detailsWheel nut used on Titan hub 90-8
Suits Titan hub 90-8
Rear tow hitch for the Agrowdrill AD083 seed drill. A rear tow hitch enables trailing machines to be hitched to the rear of the seed drill or ploug...
View full details12" FLUTED AGROWPLOW COULTER FOR SEED DRILL PCD 95mm with 5 Studs DWG 030-4055, ASP-08711 ASP lists this part as 12"
This sub-assembly fits the 400 Pasture Disc and the V slice Opener, also known as the Agrowdisc. Pairs with the 15-notch 15" Assembly: 110-3031. Pa...
View full detailsSeed tube for the 400 Pasture Disc Assembly (see 405-1000 for complete unit). Part only, no nuts or bolts supplied with this part. Fits 38mm barflo...
View full detailsTwo-piece bearing housing used to secure the 25.4mm spherical bearing to the Agrowdrill. Commonly found on older Agrowdrill models.The distance bet...
View full detailsSEALED DEEP GROOVE METRIC BALL BEARINGS
Chain tensioner made in engineering plastic, outer diameter 50mm, 80mm long.
This M8 set screw is 16mm long, zinc plated and is commonly used on the AD083 Seed Drills. It is used to secure the older AD083 Drive Offset Sprock...
View full detailsRear tow hitch to suit the AD240 Agrowdrill. Mounts centrally to 100x100mm RHS. Has Hydraulic mounts to suit 3/8" hose. Comes with Hydraulic clamps...
View full detailsTwo-piece bearing housing used to secure the 20mm spherical bearing to the Agrowdrill. Commonly found on the original Agrodrill and older models.Th...
View full detailsJoiner link to suit 10B chain. Alternate Part No.137-160
This Posi Pan Screw is used in tandem with a stainless steel spring washer to fasten the Plastic Roller Bearing Assembly onto the stainless steel v...
View full detailsThis sprocket assembly is used on the AD083 drive wheel arm assembly. It comes fitted with 2 x bearings to suit a 50mm shaft. It has 3 x M10 tapped...
View full detailsThis M16 U-Bolt is grade 8.8 and is used to secure to 100x100 RHS. It has 55mm of working thread and an overall length of 152mm from the inside fac...
View full detailsThis idle shaft is made out of 25.4mm (1") Stainless steel and is 315mm long. It has a key-way machined in the entire length of the shaft for secur...
View full details